跳至主要内容

SA 209 T1

 Seamless carbon molybdenum alloy steel boiler and superheater tubes.


ASTM A209 Grade T1a Alloy Steel Seamless Tubes are Carbon Steel Tubes with subsequent addition of chromium, molybdenum and sometimes vanadium are known as chrome Moly Tubes.


ASTM Specification alloy steel Tubes are used for high temperature service applications. Seamless Alloy Steel Tubes according to ASTM A209 Grade T1a are reheated and furnished in full annlealed,isothermal annealed or normalised quenched and tempered condition.

ASTM A209 Grade T1a Alloy Steel Seamless Tubes have a typical chemistry with additions of 0.44-0.65 Molybdenum. Bearing minimum tensile strength of 365 Mpa ASTM A209 Grade T1a Tubes have a minimum yield strength of 195 Mpa.

ASTM A209

ASTM A209 cover several grades of minimum wall thickness seamless carbon molybdenum alloy steel, boiler and superheater tubes.

This specification covers tubes 1/2 to 5 in. [12.7 to 127 mm] inclusive, in outside diameter and 0.035 to 0.500 in. [0.9 to 12.7 mm], inclusive, in minimum wall thickness.

An optional supplementary requirement is provided and, when desired, shall be so stated in the order.

The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the "M" designation of this specification is specified in the order.

Chemical Properties:
Steel GradeCSiMnSPCrMo
A209T1
SA-209T1		0.10-0.200.10-0.500.30-0.800.0200.025　0.44-0.65
A209T1b
SA-209T1b		≤0.140.10-0.500.30-0.800.0200.025　0.44-0.65
A209T1a
SA-209T1a		0.15-0.250.10-0.500.30-0.800.0200.025　0.44-0.65
Mechanical Properties:
GradeTensile strength
(Mpa)		Yield point(Mpa)
not less than		Hardness
not less than
A 209T1/SA-209 T1≥38020580HRB
A 209T1b/SA-209T1b≥36519577HRB
A209T1a/SA-209T1a≥41522081HRB

Equivalent Designation

DINENBSNFAASTMASME
DIN 17175 Grade 16Mo5–– –ASTM A209 GradeT1aASME SA 209 Grade T1a–


标签：

评论

发表评论

此博客中的热门博文

Multi-rifled seamless steel tube

  Multi-rifled seamless steel tube is used as a water wall tube loaded with a highly heated flux and is also expected to find broadened other uses in the viewpoint of iits energy saving effect and higher safety against the overheating damage. This has groove on its inside surface which functions to raise thermal efficiency by distrubing the fluid within the tube, featuring and extremely high thermal conduction property. Available grades and size range: Multi-rifled seamless steel tube are produced to meet specific end use requirements, specifications, tolerances and chemistries. Standard Grade Specification O.D.(mm) W.T.(mm) Number of rib GB/T 20409-2006 20G 15CrMoG SA-210A1 SA-210C SA-213 T2 SA-213 T12 22-83 4.5-13    4-14     Grade and Chemical Composition (%) Steel Grade C Si Mn S P Cr Mo 20G 0.17-0.23 0.17-0.37 0.35-0.65 0.015 0.025 　 　 15CrMoG 0.12-0.18 0.17-0.37 0.40-0.70 0.015 0.025 0.80-1.10 0.40-0.55 A 210A1 SA-210A1 ≤0.27 ≥0.10 ≤0.93 0.020 0.025 　 　 A 210C SA-210C ≤0.35 ≥0.10
发表评论
阅读全文

Alloy steel pipes for high pressure service

 The range of Alloy steel pipes for high pressure service pipe sizes that may be examined by each method shall be subjected to the limitations in the scope of the respective practice. Related informations : European Standards for steel ASTM Standards for steel pipes JIS Seamless Pipe Tubes for Mechanical and Automobile ASTM A335 Pipe Specifications ASTM A333 Pipe Specifications ASTM A213M-09 Standard Specication ASTM A519-89/ASME SA519 Standard specification How to packing the seamless pipe Tubes in small calibers for boilers and petro chemical industry High Temperature service tube Low temperature service tubes Note: This inventory is part of the inventory, demand and other models in stock or order materials, please contact us.
发表评论
阅读全文

ASTM A179 Heat Exchanger Tubes

  ASTM A179/A179M, ASME SA179/SA179M is the standard applicable to Seamless cold drawn low carbon steel heat exchanger and condenser tubes. When we place a specific order for SA 179 tubing, we should include below material specifications: Standard and the name of material: ASTM A179 / ASME SA 179 seamless tubes. Manufacturing types in cold drawn Size including Diameters and minimum wall thickness The factory actual scene of ASTM A179 tubes ASTM A179 Inspection Report U-Bend Fabrication Tolerances Item Condition (when) Tolercance   Nominal bend radius ≤ 2 x nominal OD less than or equal to 12% Ovality 2 x nominal OD < Nominal bend radius ≤ 4 x nominal OD less than or equal to 10%   Nominal bend radius > 4 x nominal OD  less than or equal to 5%   Nominal bend radius ≤ 2 x nominal OD 0.75 x nominal wall Mimimum wall thickness 2 x nominal OD < Nominal bend radius ≤ 4 x nominal OD 0.8 x nominal wall   Nominal bend radius > 4 x nominal OD 0.9 x nominal wall   Nominal bend radius 
发表评论
阅读全文